SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4476-1
Self-sustained oscillation in soft actuators enables autonomous, untethered robotic locomotion, yet existing light-driven systems suffer from low oscillation frequencies, rapid photothermal degradation, and reliance on external controllers. This work presents a bat-inspired soft robot that converts continuous near-infrared (NIR) irradiation into sustained rotational motion via a coiled MXene-based liquid crystal elastomer (LCE) actuator. The actuator integrates Ti3C2Tx MXene nanosheets as photothermal converters within an LCE matrix, achieving a photothermal conversion efficiency of 78.3% and a steady-state temperature of 142 °C under 1.5 W cm−2 NIR (808 nm). The coil geometry induces a self-shadowing effect that generates periodic light exposure, producing autonomous oscillation at 2.7 Hz with an amplitude of 45°. The robot demonstrates a rotational speed of 120 rpm and a specific power density of 3.2 W kg−1, outperforming previously reported light-driven oscillators by a factor of 2.5. Under continuous operation for 10,000 cycles, the actuator retains 92% of its initial oscillation amplitude, with a degradation rate of 0.008% per cycle. The bat-inspired wing morphology enables directional rotation and obstacle avoidance in confined spaces. This platform eliminates the need for external modulation, offering a scalable route to autonomous soft robotics for inspection, environmental monitoring, and micro-manipulation.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4302-9
The pre-deposited lead iodide (PbI2) film in two-step inverted perovskite solar cells (PSCs) often exhibits a dense structure, which impedes the diffusion and reaction of organic ammonium salts, leading to unreacted PbI2 residues and compromised device performance. To address this, 2,4-oxazolidinedione (OD) is introduced as a molecule additive into the PbI2 precursor solution. Owing to its stronger coordination with PbI2, OD effectively modulates its crystallization behavior, resulting in a porous structure. This porous structure significantly facilitates the diffusion and infiltration of organic ammonium salts, thereby minimizing PbI2 residue and enhancing the completeness of the perovskite conversion. Furthermore, OD and the constructed porous network jointly retard the crystallization kinetics of perovskite, promoting the formation of perovskite films with improved crystallinity and preferred crystal orientation. Therefore, the optimized PSCs achieve a power conversion efficiency (PCE) of 26.31%, and demonstrate excellent operational stability, retaining 90.24% of initial PCE for 1500 h at 25°C and 90.47% after 1000 h at 65°C. The champion device exhibits a VOC of 1.197 V, a JSC of 26.28 mA cm-2, and an FF of 83.58%, with negligible hysteresis. This study presents a straightforward yet effective approach to advancing the performance and stability of inverted PSCs fabricated via the two-step method.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3789-x
Wearable sensors have attracted significant attention due to their superior sensitivity, safety, and adaptability compared with conventional detection technologies. However, developing sustainable sensing materials that combine excellent performance with environmental friendliness remains a significant challenge. In this study, Juncus effusus (JE), a natural fiber featuring a unique internal three-dimensional (3D) network structure, was employed as the substrate. Conductive polyaniline was loaded onto the JE structure to impart electrical conductivity, and Ecoflex encapsulation provided high elasticity. Based on this approach, a JE-based resistive flexible sensor (PHE-JE) was successfully fabricated. The PHE-JE sensor exhibits high stability under various strain conditions, along with excellent flexibility and durability. Moreover, benefiting from its complex 3D structure and synergistic material interactions, the PHE-JE sensor enables accurate detection of diverse motion types, showing promising potential for future wearable sensing applications.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(25)60616-5
CuZnAl (CZA) is a classic industrial catalyst for methanol synthesis from syngas, but its catalytic performance for CO2 hydrogenation to methanol is suboptimal. The catalytic mechanism of Cu species in CZA remains challenging. This study systematically investigates the valence state changes of active Cu species in CZA catalysts and their influence on catalytic performance by modifying catalysts with varying amounts of electron donor K, thereby identifying the catalytic function of Cu species with different valence states. H2-TPR, XPS, and HR-TEM characterizations reveal that highly dispersed K species supported on CZA catalysts inhibit the reduction of CuO, resulting in a small amount of Cu2O active species being produced under reaction conditions, thus causing a decrease in catalytic activity. Furthermore, XRD and Cu LMM spectra show that the proportion of Cu0 in K-modified CZA catalysts increases with K loading, but a higher proportion of Cu0 species on the surface obviously promotes the reverse water gas shift (RWGS) reaction. According to the results of in situ infrared spectroscopy, CZA catalyst follows the reaction pathway mediated by HCOO* in the hydrogenation of CO2 to methanol.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025021902
Polyacrylonitrile (PAN) ultrafiltration membranes are widely used in water treatment, yet their anti-fouling performance remains a challenge. In this work, PAN was first reacted with sodium azide via click chemistry to synthesize 1,2,3,4-tetrazolium polyacrylonitrile (PAN-N). Subsequently, PAN-N was reacted with iodoacetamide (IAM), 2-iodoethanol (IH), iodoacetic acid (IA), and chlorosulfonic acid (CSA) to introduce hydrophilic groups, and anti-fouling PAN ultrafiltration membranes were fabricated via phase inversion. The membranes were characterized by Fourier transform infrared spectroscopy, 1H nuclear magnetic resonance, X-ray diffraction, scanning electron microscopy, and contact angle measurements. Results showed that the PAN-N membrane exhibited superior performance to pristine PAN, with water flux increasing from 0.9233 to 1.232 L·(m2·h·kPa)−1 and bovine serum albumin (BSA) rejection from 69.23% to 82.4%. Hydrophilic modification further enhanced performance; the PAN-N-IA membrane achieved the highest water flux of 1.7347 L·(m2·h·kPa)−1 and rejection of 93.57%. Anti-fouling tests revealed that modified membranes followed the order: PAN-N-CSA > PAN-N-IA > PAN-N-IH > PAN-N-IAM > PAN-N > PAN. PAN-N-CSA and PAN-N-IA showed comparable anti-fouling performance, with total fouling indices of 56.1% and 58.47%, reversible fouling indices of 47.17% and 46.97%, and irreversible fouling indices of 8.97% and 11.47%, respectively. This work demonstrates that PAN-N-IA membranes combine high flux, high rejection, and excellent anti-fouling properties, making them promising for water treatment applications.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202512066
This study addresses the removal of ammonia nitrogen (NH4+-N) and chemical oxygen demand (COD) from real coal chemical wastewater via electrochemical chlorine evolution. A nanorod-structured ruthenium dioxide catalyst (N-RuO2) was synthesized by modifying ruthenium trichloride precursor with ammonium chloride. Compared with unmodified RuO2, commercial DSA, and commercial RuO2 (Com-RuO2), N-RuO2 exhibited significantly enhanced electrochemical performance: Faradaic efficiency for chlorine evolution increased by 12.9%, 18.5%, and 25.6%, respectively; accelerated lifetime improved by 1.7, 1.9, and 2.9 times, respectively. In treating real coal chemical wastewater, N-RuO2 reduced NH4+-N to 86.4 mg·L−1 and COD to 72 mg·L−1, with degradation rate constants approximately 2.08 and 1.46 times higher than Com-RuO2, while energy consumption decreased by 17.7 Wh·g−1 and 1.5 Wh·g−1, respectively. Further studies showed that increasing chloride ion concentration enhanced removal rates and reduced energy consumption; higher current density accelerated removal but increased energy use; alkaline conditions favored NH4+-N removal, while neutral conditions favored COD removal. The excellent electrochemical performance of RuO2 nanorods indicates broad application prospects in practical water treatment.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202608007
The Minjiang River Basin, subjected to combined pollution from domestic, agricultural, and industrial sources, has become a typical sensitive area for studying the environmental behavior of emerging contaminants such as antibiotics. This study conducted a cross-year comparative analysis of the composition and concentrations of antibiotics in water samples from nine sampling sites during the dry season in November 2022 and 2024. The findings revealed: 1) After the implementation of the "National Action Plan for Reducing Antimicrobial Use in Livestock", the detection concentrations of tetracycline antibiotics (TCs) decreased (e.g., doxycycline concentrations dropped from 7.75 ng/L to undetectable levels), and the mixed risk quotient (MRQ) across the entire basin transitioned from medium to low risk. However, lincomycin (up to 4.6 ng/L), clarithromycin (1.3 ng/L), and florfenicol (0.6 ng/L) have emerged, indicating an increasing hidden ecological risk from substitution. 2) High-concentration antibiotic zones transferred from urban residential areas in 2022 to intensive aquaculture zones and upstream reservoir areas in 2024. The reduction in dry-season water flow intensified pollutant accumulation, synergistically enhancing the effects of tidal drag. Additionally, the conversion of agricultural land to aquaculture ponds led to increased use of alternative drugs (e.g., sulfamethazine), while policy interventions mitigated the exacerbation of urban antibiotic pollution by construction land. This study elucidates the migration patterns of antibiotic pollution under the synergistic effects of policy regulation and natural processes, emphasizing the need to address hidden risks of substitute drugs and the driving role of land-use changes, providing scientific basis for watershed-scale risk assessment and precise management of emerging pollutants.
SCIENCE CHINA Materials•2025•DOI: 10.1007/s40843-025-3643-8
Inverted perovskite solar cells (PSCs) suffer from defect-mediated nonradiative recombination and inefficient charge extraction, particularly at the buried interface and grain boundaries (GBs), which limit power conversion efficiency (PCE) and operational stability. This study introduces a multifunctional phosphonic acid molecule, (2-(3,6-bis(trifluoromethoxy)-9H-carbazol-9-yl)ethyl)phosphonic acid (M28), as an additive in the perovskite precursor solution. M28 spontaneously segregates toward the buried interface and GBs, fulfilling three roles: (1) slowing crystallization to enlarge grains and improve film quality, (2) passivating defects to suppress charge recombination, and (3) inducing p-type doping to create an extra electric field that promotes hole transport. Devices incorporating M28 achieve a champion PCE of 25.96% and retain 80% of initial efficiency after 1500 h of maximum power point tracking. This work demonstrates the efficacy of multifunctional phosphonic acid additives in addressing buried-interface and GB defects, offering a viable route to high-performance, stable inverted PSCs.