SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4433-5
Negative thermal expansion (NTE) and zero thermal expansion (ZTE) materials are technologically relevant for precision engineering, yet their practical deployment is constrained by narrow operating temperature windows. This study introduces an entropy-designing strategy to regulate the thermal expansion behavior in the AⅠBⅡCⅢMo3O12 system, specifically K0.4(Mg0.25Mn0.25Co0.25Ni0.25)0.4Sc1.6Mo3O12 (CE0.4MO) and related CExMO compositions (x = 0.4, 0.6, 0.8, 1.0). By tuning configurational entropy, the operating temperature windows for both NTE and ZTE are significantly broadened, with the ZTE region shifting to higher temperatures. Among single-phase compositions, CE0.4MO exhibits the lowest configurational entropy and demonstrates NTE from 100 to 830 K and ZTE up to 1100 K, surpassing most reported ZTE materials. Systematic analyses of structural evolution, lattice dynamics, and electronic structure reveal that reduced configurational entropy suppresses structural evolution, directly correlating with decreased structural flexibility. Higher atomic displacement parameters (ADPs) of oxygen in CE1.0MO provide experimental evidence for enhanced flexibility. Raman spectroscopy shows that the full width at half maximum (FWHM) of peaks in the 750–900 cm-1 range positively correlates with configurational entropy, indicating reduced lattice disorder, while modes within 750–1050 cm-1 blue-shift as entropy decreases, confirming lattice stiffening. Electron localization function (ELF) and charge density analyses indicate that Mg/Mn/Co/Ni/Sc–O bonds are ionic, with ionicity weakening as configurational entropy decreases, thereby enhancing constraints on atomic vibrations and reducing structural flexibility. This work establishes a theoretical foundation for designing thermal expansion materials with wide operating temperature ranges.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4498-7
Two-dimensional porphyrin-based hypercrosslinked polymers (TPP-HCPs) were synthesized via room-temperature interfacial polymerization using 5,10,15,20-tetraphenylporphyrin and 1,3,5-trioxane. The resulting TPP-HCPs exhibited a BET surface area of 548 m2 g-1 and a CO2 uptake of 7.97 wt% at 1 bar and 298 K. CuO/TPP-HCPs nanospheres were fabricated by thermal conversion of Cu(NO3)2·3H2O in DMF at 135 °C, using TPP-HCPs as dynamic templates. This in-situ strategy generated CuO nanoparticles within the conjugated porous matrix, facilitating electron transfer and enhancing CO2 access to catalytic centers. In CO2 electroreduction, the composite achieved a total gas Faradaic efficiency exceeding 90% at ~500 mA cm-2 (-1.4 V vs. RHE), with 40.9% for C2H4, 8.2% for CH4, 31.9% for CO, and 12.3% for H2. The catalyst maintained stability over 24 h in an H-cell. These results demonstrate that 2D conjugated polymer-templated catalysts can sustain high-rate CO2 conversion to value-added products, offering a viable route for industrial CO2 utilization.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3828-y
The rapid development of halogen-free solvent-processed organic solar cells (OSCs) has been enabled by side-chain modification on small molecular acceptors, yet the structure-property relationship between inner/outer chain lengths and device performance remains unclear. This study systematically investigates five non-fullerene acceptors (NFAs) with varied side-chain positions and architectures, clarifying the effects of inner versus outer modifications on energy level distribution, film morphology, and carrier dynamics. Notably, longer alkyl chains are not always superior; excessive solubility reduces molecular packing order. The optimized PM6:BTP-TO12 blend achieves a power conversion efficiency (PCE) of 18.2%. Furthermore, ternary OSCs incorporating BTP-TO12 as a guest material reach a remarkable PCE of 19.5%, enhancing the performance of L8-BO-based devices processed with green solvents. This improvement is attributed to the low energy loss and well-controlled aggregation behavior of BTP-TO12 in environmentally friendly toluene. These findings establish a design guideline for side-chain engineering in green-solvent-processed OSCs, achieving state-of-the-art performance and advancing scalable, eco-compatible photovoltaic technologies.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202608018
Chlorinated volatile organic compounds (CVOCs) are volatile, difficult to degrade, and highly toxic, posing serious threats to the atmospheric environment and human health. Catalytic oxidation is currently one of the mainstream methods for CVOCs abatement, owing to its high efficiency, safety, and economic feasibility, and its key aspect lies in the design and development of high-performance catalysts. In the catalytic oxidation of CVOCs, the poisoning effect of chlorine species on catalysts severely restricts catalytic performance. Ru-based catalysts, which exhibit excellent catalytic oxidation activity toward CVOCs and favorable chlorine-resistant performance, have been widely studied in recent years. This paper reviews the latest research progress on Ru-based catalysts for the catalytic oxidation of CVOCs. The mechanism of catalytic oxidation of CVOCs by Ru-based catalysts is elucidated through a systematic analysis of the relevant literature. Furthermore, the strategies for the design and structural regulation of Ru-based catalysts are outlined from the perspectives of active components, supports, and surface modification. Finally, novel preparation methods for Ru-based catalysts and the influence of reaction components on catalytic performance are summarized. Future research directions in this field are also prospected, aiming to provide a reference for the subsequent design and development of high-performance Ru-based catalysts suitable for complex operating conditions.