SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4468-6
The proliferation of multispectral detection platforms demands materials that simultaneously satisfy electromagnetic interference (EMI) shielding and infrared (IR) camouflage without compromising radio-frequency (RF) transmission. Conventional MXene films exhibit exceptional EMI shielding (>40 dB) but suffer from high IR emissivity and severe RF reflection, precluding integration with wave-transmitting arrays. This work introduces liquid metal (LM)-modified MXene composite films engineered via structural patterning to decouple optical, IR, and RF responses. The LM phase, dispersed within the MXene interlayer galleries, reduces free-electron density and tailors the dielectric loss, while a periodic array architecture creates impedance-matched windows for RF transmission. The resulting films achieve an EMI shielding effectiveness of 36 dB at 510 µm thickness, with a low IR emissivity of 0.36 and an RF transmittance exceeding 80% in the X-band. The patterning strategy suppresses surface current continuity, mitigating the trade-off between shielding and transmission. These metrics represent a 20% improvement in IR camouflage and a 15% enhancement in RF transparency relative to pristine MXene films. The composite films also demonstrate mechanical flexibility, retaining 95% of initial conductivity after 1,000 bending cycles. This work establishes a scalable route for multispectral-compatible materials critical for next-generation stealth and communication systems.
New Carbon Materials•2026•DOI: 10.1016/S1872-5805(26)61066-9
Carbon materials suffer from limited dielectric loss, resulting in poor impedance matching and inadequate microwave attenuation. To address this, hierarchical structures with synergistic loss mechanisms are sought. Here, biomass cattail serves as a sustainable precursor for nitrogen-doped carbon nanotube arrays decorated with Fe3C nanoparticles via chemical vapor deposition, yielding Fe3C@NCNTs/CMTs composites. The crystallinity, tuned by calcination temperature, critically influences microwave absorption. At 800 °C, the composite achieves a minimum reflection loss of –35.8 dB and an effective absorption bandwidth of 7.02 GHz at a thickness of only 1.7 mm, with an ultralow filler loading of 10 wt%, covering the entire Ku band and part of the X band. This performance stems from enhanced magnetic loss and multiple dielectric polarization mechanisms. The study demonstrates a promising strategy for designing biomass-derived carbon-based broadband microwave absorbers.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202604019
A two-stage electrostatic precipitator (ESP) integrating a sawtooth-rod electrode precharging unit and a plate-plate collection unit was developed for simultaneous removal of fine particles and volatile organic compounds (VOCs) from catering fumes. Using KCl particles and toluene as surrogates, the system achieved a fine particle (<0.3 µm) collection efficiency of 91% and a total particle collection efficiency exceeding 98% at applied voltages of +12 kV (sawtooth-rod) and -8.5 kV (plate-plate), with an ozone concentration of 176.9 mg/m³. The presence of particles enhanced toluene degradation, increasing removal efficiency from 29.2% to 53.1%. Positive DC discharge on the sawtooth-rod electrode yielded a higher corona current (800 µA vs. 375 µA for negative) and lower ozone generation (101.4 mg/m³ vs. 176.9 mg/m³), indicating superior suitability for catering fume treatment. The stable discharge characteristics of the sawtooth-rod electrode reduce energy consumption and extend operational cycles, offering a promising technical pathway for efficient, compact, and intelligent ESP systems in catering fume purification.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202510084
The rapid expansion of lithium battery industries has elevated lithium resources to strategic importance, yet lithium extraction generates 8–10 tons of slag per ton of lithium salt, with complex heavy metal content and high leaching risks. This study improves conventional alkali activation by employing a composite activator and multi-stage thermal assistance to achieve self-solidification of lithium slag, simultaneously immobilizing multiple heavy metals while producing high-strength materials. Under full slag conditions, the mechanical strength of solidified materials ranged from 3.48 to 8.25 MPa; after optimization, strength increased by 137.07%. Average immobilization rates for various heavy metals rose from 97.26% to 99.77%. In simulated acidic, alkaline, neutral, high-salt, acid rain, and leachate environments, efficient immobilization was maintained, with leachate concentrations below regulatory limits. The improved activator and thermal process reduced structural defects, promoted formation of the key Si-O-Al framework, and ensured structural integrity, enhancing both mechanical strength and heavy metal immobilization. The cost of slag solidification was approximately 185–200 CNY per ton, significantly lower than conventional methods, with low energy consumption, no high-temperature calcination, and reduced equipment and reagent requirements, supporting scalability.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202510029
Low hydrolysis efficiency is a core bottleneck in anaerobic digestion (AD) of lignocellulosic agricultural residues, limiting methane production and resource utilization. This study optimized thermal hydrolysis pretreatment (THP) of corn straw (CS) using response surface methodology (RSM) to enhance methane yield. The optimal conditions were determined as solid-to-liquid ratio of 51.0–57.5 mg·mL−1, pretreatment time of 74–81 min, and temperature of 182.5–197.5 °C. Under the optimal combination (52.3 mg·mL−1, 78.4 min, 191 °C), cumulative methane yield increased from 218.0 to 362.9 mL·g−1 VS, a 66.7% improvement over untreated CS. Characterization via XRD, FTIR, and SEM revealed that THP disrupted the lignocellulosic structure, reducing lignin content from 21.5% to 8.3% and crystallinity index (CrI) from 70.83% to 61.95%. Inhibitory derivatives generated during THP included furfural (1.69 mg·mL−1), 5-methylfurfural (2.44 mg·mL−1), and phenol (23.14 mg·L−1), with a theoretical combined inhibition rate of 7.26%. The promotion effect on methane production (66.7%) far exceeded the theoretical inhibition (7.26%), indicating that THP under optimized conditions is effective and environmentally controllable. This study provides a systematic framework for optimizing THP parameters to maximize methane production from agricultural residues.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60762-1
The CO2 dry reforming of methane (DRM) is pivotal for CO2 utilization within the dual-carbon framework, offering advantages in carbon reduction and value-added chemical production. However, shaped catalysts suitable for industrial-scale DRM remain limited. This work constructs a monolithic catalyst using honeycomb cordierite as the structural support, systematically investigating the effects of organic and inorganic binders on coating structure and catalytic performance. Comparative studies reveal that the active coating fabricated with inorganic aluminum sol exhibits a continuous uniform morphology and excellent adhesion strength. During high-temperature calcination, elemental diffusion within Al2O3 networks bridges the cordierite surface with active catalyst particles, forming a (Ni-Mg)AlxO4 composite structure. This creates robust metal-support interactions between active sites and the residual alumina matrix. The interconnected mesoporous framework provides superior pore confinement, contributing to strong coating adhesion, enhanced activity, and improved resistance to carbon deposition in the monolithic m-NCM-Al-sol catalyst. In contrast, coatings derived from inorganic silica sol suffer from detachment and activity loss due to heterogeneous surface structures and poor adhesion. Organic binders demonstrate inferior performance in macroscopic coating uniformity, adhesion strength, mesoporous confinement, and localized electronic effects, resulting in the poorest catalytic performance. By optimizing aluminum sol coating parameters—binder content, active component dosage, and coating cycles—a synergistic balance between coating thickness and mass transfer is achieved. The optimized catalyst demonstrates excellent DRM performance, providing insights for constructing high-performance shaped catalysts with cordierite coatings.