SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4500-8
Electroreduction of CO2 to ethylene offers a promising route for renewable electricity storage, yet achieving high ethylene selectivity at industrial current densities remains challenging due to the large energy barrier for C–C coupling. Here, we report a “MOF-assisted in situ doping” strategy to introduce the oxophilic nonmetal phosphorus (P) into the copper oxide (CuO) lattice, constructing a localized Cu–P dual-site adsorption configuration for the key *OCCHO intermediate. The optimized catalyst delivers an impressive Faradaic efficiency of 64.6% for ethylene with a partial current density of 646 mA cm-2. Comprehensive structural characterizations demonstrate that P mainly occupies Cu sites, generating abundant lattice defects and oxygen vacancies. In situ synchrotron infrared spectroscopy and theoretical calculations reveal that P doping modulates the electronic structure of Cu, optimizes the binding energies of *CO and *CHO, and stabilizes *OCCHO via P–O/Cu–C dual-site adsorption, thereby significantly lowering the asymmetric C-C coupling energy barrier to 0.74 eV. This work highlights a dual-site microenvironment regulation strategy for CO2-to-ethylene electroreduction.
Nano Research Energy•2026•DOI: 10.26599/NRE.2025.9120181
Solid-state lithium metal batteries (SLMBs) demand quasi-solid polymer electrolytes (QSSPEs) that simultaneously deliver high ionic conductivity, interfacial stability, and oxidative resistance. This study reports a QSSPE membrane (MP46) formulated with MG30:LiTFSI:succinonitrile at a 10:4:6 weight ratio, exhibiting a wide electrochemical window of 5.1 V. Complementary infrared spectroscopy, small-angle X-ray scattering, and electron microscopy reveal a hierarchical ionic conductive network consisting of sphere-like nanostructures embedded within microphase-segregated architectures. This morphology enhances lithium-ion transport while preserving mechanical integrity. The strong interfacial adhesion between MP46 and lithium metal enables stable lithium plating and stripping for over 800 h at 0.2 mA·cm–2, effectively mitigating dendrite formation. When paired with LiFePO4 and LiCoO2 cathodes, MP46 sustains prolonged cycling, retaining 80.1% capacity after 1400 cycles at 2 C and 92.1% after 200 cycles at 4.5 V, respectively. Pouch-type cells further demonstrate mechanical flexibility and operational safety under deformation. These results establish MP46 as a viable candidate for stable high-energy-density SLMBs, offering fundamental insights into the design of next-generation polymer electrolytes.
New Carbon Materials•2026•DOI: 10.1016/S1872-5805(26)61097-9
Silicon/carbon (Si/C) composites are promising anode materials for high-energy-density lithium-ion batteries (LIBs) because they mitigate the severe volume expansion and poor electrical conductivity of pure silicon anodes. This review systematically summarizes the state-of-the-art preparation methods for Si/C composites, including ball milling, spray drying, electrostatic spinning, and chemical vapor deposition (CVD). Structural engineering strategies, such as carbon precursor coating, silicon-precursor-based wet chemistry, and silicon surface modification, are critically assessed for their effectiveness in enhancing electrical conductivity, buffering volume changes, and improving overall electrochemical performance. The review highlights that while Si offers a theoretical capacity of 4200 mAh g−1, far exceeding graphite's 372 mAh g−1, its practical application is hindered by capacity fading and low initial coulombic efficiency. The integration of carbon matrices not only provides mechanical flexibility but also facilitates electron transport. Key performance metrics from recent studies, including specific capacities exceeding 1000 mAh g−1 and improved cycling stability over hundreds of cycles, are discussed. The review also addresses the challenges of scalable production and cost-effectiveness, emphasizing the need for optimized precursor selection and processing parameters. Future research directions are proposed, focusing on the rational design of hierarchical structures and the development of novel binders to further enhance the long-term durability of Si/C anodes. This comprehensive overview serves as a valuable resource for researchers and engineers aiming to advance the commercialization of high-energy-density LIBs.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4044-3
Efficient sequestration of radioactive iodine species (I2, CH3I, I3−) is vital for nuclear safety and environmental protection. However, developing multifunctional adsorbents that remain effective under diverse conditions remains a significant challenge. Herein, we report two functionalized PD-COFs (PD-WS and PD-WY) with moderate crystallinity, outstanding thermal stability, and robust chemical resistance. They exhibit superior adsorption performance in both gas and liquid phases. Specifically, at 75°C, PD-WY achieves capacities of 4.88 g g−1 for I2, 1.55 g g−1 for CH3I, and 5.55 g g−1 for the I2/CH3I mixture, while high capacities are also retained at room temperature. In solution, PD-WY adsorbs up to 3.56 g g−1 of I3− in water and 2.00 g g−1 of iodine in cyclohexane. These COFs display rapid kinetics (K80% = 3.25 g g−1 h−1 for I2 and 7.89 g g−1 h−1 for I3−) and excellent selectivity. Mechanistic studies indicated that the excellent iodine affinity of PD-COFs arises from their rich electronic structures, abundant active sites, and charge transfer interactions. These findings position PD-COFs as highly promising adsorbents for nuclear waste treatment and environmental remediation.