SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4448-y
Zero-dimensional (0D) hybrid metal halides are promising for optoelectronic displays, bioimaging, and anti-counterfeiting due to strong exciton localization and self-trapped exciton (STE) emission. However, low-toxicity, biocompatible zinc halides with blue emission remain scarce, hindered by structural isolation of [ZnBr4]2− tetrahedra, electron-phonon coupling, lattice distortion, and nonradiative relaxation. Here, we synthesize MPAZnBr4 (MPA = N-(3-aminopropyl) morpholine), a 0D zinc bromide halide. Single-crystal X-ray diffraction reveals a monoclinic P21/c space group with a = 6.65190 Å, b = 16.11210 Å, c = 13.79640 Å, β = 94.5700°, Z = 4, and a calculated density of 2.394 g/cm3. The isolated [ZnBr4]2− tetrahedra are hydrogen-bonded to MPA cations, with the shortest Br···Br contact of 4.76 Å indicating weak inter-cluster electronic coupling. Upon photoexcitation, MPAZnBr4 exhibits bright blue emission centered at 450 nm with a full width at half maximum of 135 nm. Wavelength-dependent emission mapping confirms a single radiative pathway, while temperature-dependent photoluminescence identifies triplet STE emission with a thermal quenching activation energy of 55 meV. The extensive hydrogen-bonding network imparts remarkable structural stability, showing negligible photoluminescence decay under prolonged excitation or storage. As a proof-of-concept, we demonstrate switchable and rewritable information encryption and decryption, enabling complex luminescent patterns. These findings provide a strategy for constructing highly stable, low-toxicity blue-emissive Zn-based 0D metal halides for advanced photonic and information-security applications.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60647-0
Photoelectrochemical (PEC) water splitting offers a direct route to convert solar energy into clean hydrogen fuel. CuBi2O4, a p-type semiconductor with a bandgap of 1.5–1.8 eV, exhibits visible-light responsiveness and good stability, yet its performance is limited by high interfacial resistance and severe charge carrier recombination. This study introduces a CuO interlayer between fluorine-doped tin oxide (FTO) and CuBi2O4 to construct CuO/CuBi2O4 photocathodes, aiming to improve interfacial charge transfer. The optimized CuO/CuBi2O4-200 photocathode achieved a photocurrent density of −1.71 mA/cm² at 0 V vs. RHE, more than 3.5 times that of bare CuBi2O4. Incident photon-to-current efficiency (IPCE) at 365 nm reached ~13%, and the maximum applied bias photon-to-current efficiency (ABPE) was 0.17%. Water splitting experiments yielded 2.05 μmol/cm² of hydrogen, significantly surpassing the unmodified photoelectrode. Mechanistic studies indicate that the CuO layer establishes favorable band alignment, promotes hole transport toward the FTO substrate, and suppresses interfacial carrier recombination. This work demonstrates a simple and efficient interfacial engineering strategy, offering insights for the design of high-performance semiconductor-based PEC photoelectrodes.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202606006
Chitosan-based microsphere composites have attracted considerable attention for phosphorus adsorption due to their facile preparation, low cost, environmental friendliness, and high uptake capacity. This review summarizes the physicochemical properties and preparation methods of chitosan microspheres for phosphate removal, outlines common modification strategies to enhance adsorption capacity, and discusses their applications in aqueous environments. Adsorption mechanisms, regeneration, and resource recovery of spent microspheres are analyzed. Challenges and recommendations are proposed, including streamlined preparation, enhanced phosphorus recovery, removal of multiple phosphorus forms, and practical implementation. The review aims to guide the development of high-performance chitosan-based microspheres for phosphorus removal.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202511043
Zero-valent iron (ZVI) suffers from surface passivation and low electron utilization in reductive removal of nitrobenzene (NB). To address these issues, a ball-milled iron/digestate biochar composite (BM-Fe/DBC) was prepared and compared with a physically mixed counterpart (PM-Fe/DBC). Characterization revealed that ball milling tightly embedded ZVI particles into the carbon matrix, forming Fe–C chemical bonds and a strong interfacial coupling structure that established efficient electron transfer channels. This structure significantly enhanced the micro-galvanic effect between iron and carbon, yielding superior reduction performance across a wide pH range (3–9). Under optimal conditions (Fe:C mass ratio 2:1, dosage 1.0 g·L−1, pH 5), BM-Fe/DBC achieved 79.9% NB removal, and the generation of aniline (AN) was 1.85 times that of PM-Fe/DBC. Mechanistic studies indicated that the intimate Fe–C interfacial coupling promoted sustained ZVI corrosion and enhanced the production of indirect reducing species, including adsorbed Fe(II) and atomic hydrogen (H*). Electrochemical analyses showed that BM-Fe/DBC exhibited a lower corrosion potential, a higher corrosion current density (approximately 2.15 times higher), and lower charge transfer resistance, kinetically confirming its superior electron transfer capability. These findings reveal that constructing strong interfacial coupling in iron–carbon composites via mechanochemical methods can effectively overcome key limitations of ZVI in reduction reactions, providing a theoretical basis and practical pathway for designing high-performance water treatment materials.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202408057
Urban waterlogging, exacerbated by climate change and rapid urbanization, poses increasing risks, particularly in coastal low-lying areas with dense river networks. This study simulated waterlogging in the Shajing River drainage area of the Maozhou River basin, Shenzhen, using the SOBEK hydrodynamic model. Under a 5-year return period rainfall, 47 manholes overflowed and 31.29% of stormwater pipes operated at full capacity. Twelve waterlogging-prone points were identified: eight due to insufficient drainage capacity and five due to river backflow from low elevation. Two optimization schemes were compared: enlarging pipe diameters and implementing Low Impact Development (LID) measures. Pipe enlargement reduced overflowing manholes by 32 and full-flow pipe length by 20%, effectively decreasing surface ponding. LID measures reduced overflowing manholes by only 4 and full-flow pipe length by 1.5%, but decreased maximum flooding depth by nearly 1 m, alleviating drainage system burden. The study highlights the complex causes of coastal urban waterlogging, especially river backflow under tidal influence, and recommends considering sea-level rise and storm surge in drainage design. The findings provide valuable references for attributing waterlogging causes and planning drainage network upgrades in coastal cities.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3978-0
All-polymer solar cells (all-PSCs) are promising for flexible and wearable electronics due to their excellent stability and mechanical stretchability. However, achieving high performance remains challenging due to difficulties in controlling the morphology of polymer blend films. In this study, a novel polymer donor, PBDTF-DTP, incorporating a weak electron-withdrawing yet large-dipole-moment dithienylphthalimide (DTP-2T) unit, was rationally designed and synthesized for ternary all-PSCs. Introducing PBDTF-DTP as a guest donor enables complementary light absorption and deepens the highest occupied molecular orbital level, simultaneously improving short-circuit current density (J_SC) and open-circuit voltage (V_OC). The large dipole moment of DTP-2T increases the dielectric constant, suppressing non-radiative energy loss and further boosting V_OC. Notably, PBDTF-DTP exhibits a relatively higher molecular electrostatic potential than the host donor, effectively tuning compatibility with both polymer donor and acceptor, regulating blend morphology, and promoting formation of a nanoscale fibrillar network. This optimized morphology facilitates efficient charge generation and transport while suppressing charge recombination. Consequently, ternary all-PSCs based on PM6:PBDTF-DTP:PYIT achieve a synergistic enhancement in J_SC, V_OC, and fill factor, yielding a remarkable power conversion efficiency of 18.01%, significantly higher than that of binary PM6:PYIT devices (15.51%). This study demonstrates that combining electrostatic potential optimization with a ternary strategy provides an effective approach to regulate morphology and achieve high-efficiency all-PSCs.