SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3642-4
High-density glass scintillators are promising alternatives to crystals for next-generation radiation detection due to their low cost, excellent physical and chemical stability, and processability. In this study, a series of Ce3+-activated gadolinium gallium borosilicate (GGBS x) glasses were synthesized via vacuum melt-quenching. With increasing Gd2O3 content, glass density increased from 5.86 to 6.05 g/cm3, and molar volume from 36.43 to 39.79 cm3/mol. Extended X-ray absorption fine structure (EXAFS) analysis revealed that in GGBS 1 glass, Ce3+ exclusively adopts a hexahedral [CeO6] configuration, while Gd3+ exhibits both hexahedral and octahedral coordination with a bond length of 2.35±0.1 Å and Debye-Waller factor σ2 of 0.0122±0.0015 Å2. As Gd2O3 content increased, shallow trap depth rose from 0.804 to 0.858 eV, while deep trap depth first increased from 0.948 to 1.434 eV then decreased to 1.010 eV. GGBS 1 glass exhibited high transmittance (~80%) in the visible range and a photoluminescence quantum yield of 78.4%. Under X-ray irradiation, its X-ray excited luminescence intensity reached 128.5% of that of Bi4Ge3O12 (BGO) crystal, with a spatial resolution of 29.1 lp/mm, approaching the highest reported for glass scintillators. Under γ-ray excitation, it achieved a light yield of 1058 photons/MeV and an energy resolution of 23.7% at 662 keV. These results indicate that GGBS 1 glass scintillator warrants further development for applications in X-ray imaging and γ-ray spectroscopy.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3748-9
Direct regeneration is a sustainable solution for recycling spent lithium-ion batteries (LIBs), yet the irregular strains induced by the irreversible FePO4 phase after cycling hinder Li+ replenishment in spent LiFePO4 cathodes. This study proposes a lattice stress modulation strategy that reduces FePO4 to Fe2P2O7, reducing unit cell volume from 271.7 to 122.6 Å3, releasing residual stress and reconstructing continuous Li+ transport channels. The phase transformation reconstructs FeO6 octahedra, lowering the migration energy barrier for ions. This synergistically weakens steric effects, facilitating Li+ replenishment and eliminating Li-Fe anti-site defects. Regenerated LiFePO4 cathodes achieve 80.2% capacity retention after 1000 cycles at 2C, outperforming commercial cathodes. The work establishes fundamental principles for the pre-treatment stage of direct regeneration and provides a paradigm-shifting solution for sustainable LIB recycling.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202606020
Municipal wastewater treatment plants in China face excessive influent grit loads and carbon source deficiencies, while conventional pretreatment (screening, grit chambers, primary sedimentation) exhibits low fine grit removal and poor carbon retention. A novel swinging ultra-fine screen with a screening precision of 0.1 mm was developed and tested at a pilot scale of 1000 m³/d. Systematic evaluation of screens with apertures from 0.05 to 0.4 mm was conducted, with mechanisms analyzed via particle size distribution, COD fractionation, and fouling layer characterization. The 0.1 mm screen achieved an SS removal efficiency of 89.3%, significantly higher than 57.4% for conventional processes, while COD removal was only 9.5% versus 28.6%, corresponding to a carbon source retention of 93%. The device nearly completely retained particles >0.1 mm and achieved >98% removal for particles in the 0.075–0.1 mm range. Performance remained stable under fluctuating COD and SS conditions. A three-stage fouling theory for micro-screens was proposed. This work represents the first application of 0.1 mm screening precision in pretreatment, markedly improving fine grit retention and carbon source preservation, with strong resilience to water quality variations.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025042802
Activated carbon, characterized by its extensive pore structure, high specific surface area, and superior adsorption capacity, is widely employed in advanced water treatment. However, upon reaching adsorption saturation, its efficacy diminishes, necessitating replacement or regeneration. Thermal regeneration stands out due to its high desorption efficiency, simple equipment requirements, and low energy consumption, making it the predominant industrial method. Despite its prevalence, systematic investigations into the underlying reaction mechanisms and the influence of operational parameters remain insufficient. This review comprehensively examines common thermal regeneration technologies for saturated activated carbon, including multi-hearth furnaces, rotary kilns, superheated steam, microwave, and solar regeneration. It delineates the fundamental principles, process flows, advantages, disadvantages, and current research status of each method. The desorption and reaction mechanisms of pollutants within activated carbon pores during thermal regeneration are discussed in detail, along with the effects of critical conditions such as temperature, atmosphere, and purge gas flow rate on pollutant removal efficiency. Furthermore, the relationship between activated carbon performance parameters and regeneration efficiency is analyzed, and innovations based on conventional thermal regeneration, as well as integration with emerging technologies, are explored. Finally, the challenges facing thermal regeneration are summarized, and future research priorities are proposed, focusing on the treatment of waste gas and liquid byproducts, technology integration, and enhancement of overall regeneration performance. This review aims to provide a scientific foundation for the sustainable recycling of activated carbon in industrial applications.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4035-5
Electrocatalytic CO2 reduction reaction (CO2RR) to formate offers a promising pathway for storing renewable electricity in chemical fuels and enabling carbon recycling. The development of efficient and stable catalysts for this specific pathway, however, remains a central challenge. Heteroatom doping can significantly tune the interaction between active sites and key intermediates, boosting catalytic performance. Conventional doping in Bi-based catalysts often relies on uncontrollable in-situ electrochemical processes, leading to ineffective bulk incorporation. Here, we present a simple pre-doping strategy that enables precise doping at surface active sites, thereby enhancing electrochemical performance. The resulting catalyst achieves >95% Faradaic efficiency for formate across 100–500 mA cm−2 in a flow cell and maintains >95% efficiency for over 70 h at 100 mA cm−2 in a membrane electrode assembly, outperforming pure Bi and Bi2S3. A solar-driven system further demonstrates a 4.4% solar-to-formate conversion efficiency. Mechanistic studies reveal that sulfur doping increases electron density, stabilizes the key *OCHO intermediate, and suppresses hydrogen evolution. These findings provide valuable insights into the precise pre-doping modulation of surface active sites for designing highly efficient and stable CO2RR catalysts.