New Carbon Materials•2026•DOI: 10.1016/S1872-5805(26)61066-9
Carbon materials suffer from limited dielectric loss, resulting in poor impedance matching and inadequate microwave attenuation. To address this, hierarchical structures with synergistic loss mechanisms are sought. Here, biomass cattail serves as a sustainable precursor for nitrogen-doped carbon nanotube arrays decorated with Fe3C nanoparticles via chemical vapor deposition, yielding Fe3C@NCNTs/CMTs composites. The crystallinity, tuned by calcination temperature, critically influences microwave absorption. At 800 °C, the composite achieves a minimum reflection loss of –35.8 dB and an effective absorption bandwidth of 7.02 GHz at a thickness of only 1.7 mm, with an ultralow filler loading of 10 wt%, covering the entire Ku band and part of the X band. This performance stems from enhanced magnetic loss and multiple dielectric polarization mechanisms. The study demonstrates a promising strategy for designing biomass-derived carbon-based broadband microwave absorbers.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3748-9
Direct regeneration is a sustainable solution for recycling spent lithium-ion batteries (LIBs), yet the irregular strains induced by the irreversible FePO4 phase after cycling hinder Li+ replenishment in spent LiFePO4 cathodes. This study proposes a lattice stress modulation strategy that reduces FePO4 to Fe2P2O7, reducing unit cell volume from 271.7 to 122.6 Å3, releasing residual stress and reconstructing continuous Li+ transport channels. The phase transformation reconstructs FeO6 octahedra, lowering the migration energy barrier for ions. This synergistically weakens steric effects, facilitating Li+ replenishment and eliminating Li-Fe anti-site defects. Regenerated LiFePO4 cathodes achieve 80.2% capacity retention after 1000 cycles at 2C, outperforming commercial cathodes. The work establishes fundamental principles for the pre-treatment stage of direct regeneration and provides a paradigm-shifting solution for sustainable LIB recycling.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202507046
Addressing the insufficient applicability and accuracy of carbon footprint accounting for electromechanical products due to data gaps, this study proposes an accounting method based on life cycle assessment (LCA). Using LCA as the overall framework with a system boundary of "cradle to gate", the method constructs a carbon footprint accounting approach combining substitution algorithms and correction coefficients for different data missing scenarios from suppliers, manufacturers, and databases. Data quality indicators and Monte Carlo simulation are employed to quantify data quality and uncertainty, while single-factor and multi-factor sensitivity analyses identify key influencing factors. Taking an optical gyrocompass as a case study, the carbon footprints and uncertainties under eight typical data missing scenarios are explored, and robustness checks are conducted on five typical products including transformers, high-speed diesel engines, and wind turbines. As data missing degree deepens, the carbon footprint deviation of the optical gyrocompass increases from 0.05% to 3.03%, and uncertainty rises from 2.65% to 5.45%. Under mixed data missing scenarios, the carbon footprint uncertainties of all five electromechanical products remain below 10%. The method exhibits wide applicability, strong implementability, and high accuracy, effectively supporting carbon footprint accounting for electromechanical products, reducing carbon tariff risks, optimizing emission reduction strategies, and promoting green development.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(25)60607-4
The methanation of biomass gasification syngas (H2/CO = 3:1) was investigated over Ni/Al2O3 monolithic catalysts supported on cordierite, with a nominal Ni loading of 15 wt%. Catalysts were modified by treatment with 10% NaOH solution for 1 h and 2 h. Physicochemical properties were characterized by BET, TEM, H2-TPR, XRD, CO2-TPD, and TG. Results showed that the 2 h modification (15%Ni/Al2O3-2h) increased specific surface area, enhanced catalytic activity, and increased alkaline site density compared to the unmodified catalyst. Under optimized conditions (H2/CO volume ratio 3:1, space velocity 10000 mL/(g·h), temperature 400 °C), the 15%Ni/Al2O3-2h catalyst achieved a CO conversion of 97% and CH4 selectivity of 100%. Stability tests over 2 h showed that the CO conversion remained stable at approximately 98%, indicating excellent catalytic stability. The study demonstrates that alkali modification with 10% NaOH for 2 h significantly improves both the methanation performance and stability of Ni/Al2O3 monolithic catalysts, offering a promising route for synthetic natural gas production from biomass.
Chinese Journal of Environmental Engineering•2026•DOI: 10.12030/j.cjee.202508053
Polycyclic aromatic hydrocarbons (PAHs) in industrial soils pose significant risks due to their hydrophobicity and low bioavailability, limiting the efficacy of bioremediation. This study investigated the enhancement of an in-situ electrokinetic-biological barrier (EK-BB) system for PAH-contaminated soil using biosurfactants. Three biosurfactants—rhamnolipid (RL), alkyl polyglycoside (APG), and saponin (SAP)—were applied individually and in combinations at 10× critical micelle concentration (CMC), and the optimal RL+APG mixture was further tested at 2.5, 5.0, 7.5, and 10× CMC. Results showed that biosurfactant application improved soil electrical current, moisture retention, and PAH removal. Combined surfactants outperformed single ones, with the 10× CMC RL+APG treatment (Exp IV) achieving the highest average current intensity and moisture content, 1.31 and 1.12 times that of the control (CK), respectively, and a PAH removal of 106.02 mg·kg⁻¹. Biosurfactants also promoted bacterial growth in both contaminated soil and the biobarrier layer; the 10× CMC RL+APG treatment increased bacterial counts by 6.24-fold and 44.8%, respectively. However, excessive surfactant concentrations led to PAH accumulation in the biobarrier and clean soil. The 5× CMC RL+APG treatment provided optimal balance, maximizing PAH removal while maintaining barrier effectiveness. These findings confirm that appropriate biosurfactant concentrations can enhance EK-BB remediation, offering technical support for PAH-contaminated site remediation and safe reuse.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3976-x
The discovery of high-temperature superconductivity in bilayer nickelate La3Ni2O7−δ (La-327) under high pressure and in thin films at ambient pressure has opened new avenues in superconductivity research. However, La-327 exhibits a narrow phase stability range, leading to stacking faults that suppress bulk superconductivity. Chemical substitutions, particularly at the A-site with smaller rare-earth ions, have been shown to enhance phase purity and reduce stacking faults, while also increasing the orthorhombic distortion and chemical pressure. In this work, we apply the high-entropy (HE) strategy to stabilize the 327 phase with reduced average A-site ionic radius (rA). We successfully synthesized medium-entropy La1.2Pr0.6Nd0.6Sm0.6Ni2O7−δ (ME-327) and high-entropy La0.67Pr0.67Nd0.67Sm0.33Eu0.33Gd0.33Ni2O7−δ (HE-327) polycrystalline samples. These compositions satisfy medium- and high-entropy criteria, with rA values of 1.181 Å and 1.164 Å, respectively. The samples are phase-pure and homogeneous. HE-327 exhibits the lowest cell volume, largest orthorhombicity, and shortest interlayer Ni-Ni distance among reported bilayer nickelates. Physical property measurements reveal low electrical conductivity and a high density-wave (DW) transition temperature. Under high pressure, HE-327 shows a resistivity anomaly at 103 K under 31 GPa, suggesting a possible superconducting transition. Extrapolation indicates that Tc under high pressure exceeds 100 K for HE-327, correlating with reduced rA and enhanced interlayer coupling. Our results demonstrate the ionic size effect and the effectiveness of the HE approach in stabilizing bilayer nickelates, providing a new avenue for developing superconducting materials.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(25)60628-1
The coupling of CO2 with olefins to produce cyclic carbonates has emerged as an important research topic in sustainable chemistry, owing to its high atom economy and the wide applicability of the resulting products. However, this reaction faces a significant challenge due to the mismatch between the rates of the epoxidation and cycloaddition steps. In this work, a series of TS-1 zeolite catalysts encapsulating different amounts of molybdenum acetylacetonate were prepared through hydrothermal synthesis followed by post-treatment, with the aim of elucidating the rate balance between the epoxidation and cycloaddition steps and the underlying regulation mechanism. Characterization results show that the Mo species were present as highly dispersed molybdenum acetylacetonate complexes that were stably confined within the TS-1 framework. These complexes interact electronically with the tetra-coordinated Ti sites to form synergistic active centers, while imposing negligible effects on the zeolite structure and porosity. In the CO2-styrene coupling reaction, tuning the Mo loading enabled effective control over the epoxidation rate, thereby achieving an appropriate balance with the subsequent cycloaddition step. The optimized catalyst delivered excellent performance under mild conditions, with a styrene conversion of 83.4% and a selectivity of 75.3%, and also exhibited outstanding recyclability. Overall, this encapsulated catalyst successfully addresses the dual challenges of rate matching and active-site stability in CO2–olefin coupling, providing valuable insights for the rational design of efficient, durable bifunctional catalysts.
Environmental Chemistry•2026•DOI: 10.7524/j.issn.0254-6108.2025050803
This study systematically investigates the synergistic drag reduction mechanism of surfactants and porous media in coal seam water injection. Four surfactant types—cationic CTAB, anionic SDBS, amphoteric BS-12, and nonionic OP-10—were tested with five porous media pore sizes (3–12 mm) using a custom-built all-in-one drag reduction test system. The effects of surfactant type, mass concentration, driving frequency, and pore diameter on drag reduction efficiency were evaluated. Results show that in an empty tube, drag reduction efficiency increases with mass concentration. As driving frequency increases, drag reduction first rises then falls, peaking at 35 Hz. With porous media, drag reduction exhibits pore size dependence, reaching a maximum at 8 mm and decreasing thereafter. The composite surfactant-porous media system achieves synergistic enhancement over single systems. At 0.05% mass concentration, all surfactants attain maximum drag reduction, with CTAB showing the highest efficiency. Optimal conditions (0.05% CTAB, 35 Hz, 8 mm pore size) yield a drag reduction rate of 66.14%, a 1.4-fold improvement over 20 Hz. These findings demonstrate that tailoring surfactant and porous media parameters can significantly optimize coal seam water injection efficiency, offering a practical approach for dust control in mining.