SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-026-4447-3
Chargeable photoconductivity, a non-volatile photoresponse phenomenon, was investigated in multiferroic heterostructures comprising Bi0.85La0.15FeO3 (BLFO) and a quasi-two-dimensional electron gas (Q2DEG). Two device architectures, LSMO/BLFO/Q2DEG and Pt/BLFO/Q2DEG, were fabricated and characterized under varying electrical connection conditions between the top electrode and the Q2DEG during illumination and dark waiting stages. Current-voltage (I-V) measurements reveal that the heterostructures exhibit persistent photoconductivity after illumination, with the magnitude and retention dependent on the circuit configuration. Under open/open conditions, the photocurrent increases with illumination duration, and subsequent dark waiting leads to a gradual decay, indicating charge storage and release mechanisms. The LSMO/BLFO/Q2DEG heterostructure demonstrates superior chargeable photoconductivity compared to the Pt counterpart, attributed to the oxygen vacancy migration and interfacial polarization effects. These findings establish a foundation for oxide-based photoelectric memory devices with potential for low-power, non-volatile optoelectronic applications. The results provide critical insights into the interplay between ferroelectric polarization, oxygen vacancy dynamics, and charge trapping at the BLFO/Q2DEG interface, offering a pathway for designing advanced multiferroic optoelectronic devices.
Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202605018
To address the inadequacy of existing temporal emission allocation coefficients for oil storage, transportation, and sales sources in regions with distinct seasonal temperature variations, this study focused on a large oil depot in Northwest China. A method for establishing temperature-dependent hourly allocation coefficients for VOCs emissions was proposed, revealing a positive correlation between ambient temperature and emission coefficients. The coefficient peaked at 0.068 when temperatures exceeded 14 °C and dropped to a minimum of 0.007 below 8.5 °C. Annual VOCs emissions totaled 256.13 t, with summer contributing 108.89 t (42.51% of annual total) and winter only 12.54 t (4.90%), making summer emissions approximately 8.68 times higher than winter. Using CALPUFF dispersion modeling, dynamic source strength scenarios produced a maximum hourly concentration of 2242.7 μg/m³, a 55.12% increase over the constant source strength scenario (1445.8 μg/m³). The area of exceedance increased by 0.03 km², and the atmospheric environmental protection distance extended by 450 m, from 0 m to 450 m. These results demonstrate that conventional constant emission assumptions underestimate peak concentrations and protection distances, posing health risks to nearby residents. The study provides a scientific basis for localized emission regulation and improved environmental protection distance calculations.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3814-2
Micro-structured surfaces have attracted increasing attention due to their great potential applications. However, it is still a challenge to continuously fabricate micro-structured surfaces based on thermoplastics by a facile, low-cost, and environmentally-friendly method. Herein, with the help of the extrusion molding method and an elaborately designed mold, micro-grooved fiber (MGF) based on high-density polyethylene (HDPE) is continuously prepared. Theoretically, infinitely long MGFs with feature sizes down to a few microns can be efficiently fabricated because of the continuous fabrication characteristic of the melt extrusion method. Interestingly, left- and right-handed micro-grooves with different helix angles can be produced by applying twisting at the die exit, and the macroscopically MGF springs can be further fabricated via a self-designed three-dimensional helical enwind device. By regulating wettability, MGF can achieve liquid self-transport on predefined paths. In addition, MGF fabric exhibits rapid evaporation behavior, whose evaporation rate is about 4 times higher than that of the Smooth fiber (SMF) fabric and 2 times higher than that of the most popular commercial quick-drying fabric (i.e., Cool-max fabric). This work proposes a facile and environmentally-friendly method for continuously preparing low-cost and flexible MGF, opening a new pathway to develop fiber-based microfluidic systems following the concept of "functionalized processing for thermoplastics".
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60636-6
Polyoxymethylene dimethyl ethers (DMMx) are promising clean diesel additives. Compared to the traditional aldol condensation route, the one-step oxidative method for producing DMMx directly from methanol is a green synthesis route offering significant advantages. However, due to the complexity of the reaction, a balance must be struck between oxidation depth and C–O chain growth efficiency. This imposes specific requirements on the design of catalysts with multifunctional active sites: the catalyst should possess appropriate oxidative activity, suitable acid strength distribution, and effective synergy between these two functions. To address these challenges, this study designed a sulfuric acid-modified molybdenum-doped NASICON catalyst, which demonstrated favorable catalytic performance in the one-step oxidative synthesis of DMMx from methanol. Over the NSC-Mo-0.5-30% catalyst, methanol conversion rate of 81.3% and the DMMx selectivity of 58.7% were achieved, along with the formation of heavier molecules, as evidenced by the DMM2–6 selectivity of 11.3%. The NH3-TPD, Py-IR and XPS results indicate that the introduction of molybdenum increases the number of weak Lewis acid sites, while sulfuric acid impregnation not only generates gradient-distributed Brønsted acid sites but also promotes the formation of Mo5+/Mo6+ redox pairs. The cooperation of the two types of active sites significantly enhances catalyst performance.