Journal of Environmental Engineering Technology•2026•DOI: 10.13205/j.hjgc.202605012
The extraction process of large-scale infiltration galleries significantly alters surface water-groundwater exchange dynamics. Existing models often simplify the gallery as a boundary condition or adopt loosely coupled schemes, constrained by iterative exchange algorithms, failing to capture dynamic water flux interactions and transient responses. This study focuses on the large riverbed infiltration and purification water supply project in Shijiazhuang, China, establishing an integrated three-domain fully coupled numerical model—encompassing surface water, groundwater, and the infiltration gallery—using the dual-node coupling approach in HydroGeoSphere. The model sets two upstream inflow scenarios (wet and dry seasons) and simulates groundwater level evolution and water exchange processes under two operational modes: single-pump extraction at 1000 m³/h and no pumping. Results show that groundwater levels decline markedly under pumping, with the most pronounced response in the dry season, where maximum drawdown reaches approximately 1.24 m. Monitoring wells near the gallery show an earlier hydraulic response to pumping, reaching peak drawdown rates about 2–3 days sooner than wells farther away. At steady-state balance, surface water contributes more recharge to groundwater during the wet season than in the dry season, and water exchange between the gallery and aquifer is substantially enhanced under pumping. Spatially, water exchange concentrates primarily around transverse and longitudinal gallery sections, consistent with localized permeability enhancement from the perforated structure. These findings reveal groundwater dynamics and multi-domain interaction mechanisms under operational conditions, providing a theoretical basis for planning, design, and management of similar riverbed infiltration projects.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3794-0
Luminescent transparent display technology is widely used in emerging fields such as augmented reality glass, head-up vehicle display, and commercial retail windows. While electroluminescent display is well established, the photoluminescent transparent screen of full-color rendering ability remains elusive due to the severe crosstalk between emitters. Herein, a full-color transparent screen of an orthogonal red/green/blue (R/G/B) luminescence is reported. Lanthanide fluoride nanocrystals are used as the emitters, where the color is tuned by a deliberate choice of doping activators including Tb3+, Eu3+, and Tm3+. Polyvinyl alcohol, with an identical refractive index to nanocrystals, is employed as the host matrix, enabling a high transparency up to 86% in the visible region upon a high loading content (~78 wt%) of nanocrystals. It should be noted that the nanocrystals are embedded in separate monolayers before integration by a UV-selective absorber, i.e., epoxy resin, which absorbs 254-nm UV to block cross-excitation between Tb3+ and Eu3+ layers, providing an asymmetric luminescent property from both sides of the screen. In a proof-of-concept experiment, a full-color prototype is showcased in real time for its potential applications in advanced displays of immersive experience.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-3968-3
The commercialization of perovskite solar cells (PSCs) is hindered by stability issues primarily stemming from interfacial defects. This study employed a machine learning (ML) screening approach and constructed a learnable weighted ensemble model (LWEM) to enhance prediction robustness for identifying effective interface passivation materials. The ML model predicted that an imidazolium salt-based interface modifier, 1-benzyl-3-methylimidazolium tetrafluoroborate (BMT), is suitable for planar n-i-p PSCs. Subsequent experimental results demonstrated that BMT provides synergistic passivation via an 'ion-coordination dual-lock' mechanism that significantly suppresses non-radiative recombination, facilitates hole extraction, and improves the quality of the perovskite film. The BMT-modified devices achieve a significant increase in power conversion efficiency (PCE) from 22.45% to 24.89% under AM 1.5G illumination, and attain a high PCE of 41.31% under 1000 lux light emitting diode (LED) indoor lighting. Additionally, the modified devices exhibit outstanding stability under long-term storage and maximum power point tracking conditions. This work provides a strategy for developing high-performance and highly stable PSCs for both indoor and outdoor applications.
Journal of Fuel Chemistry and Technology•2026•DOI: 10.1016/S1872-5813(26)60664-0
The selective hydrogenation of biomass-derived furfural (FAL) to high-value chemicals such as furfuryl alcohol (FOL) or tetrahydrofurfuryl alcohol (HFOL) is pivotal yet challenging due to the need for precise control over reaction pathways. In this study, a Ni2Al-LDO (layered double oxide) catalyst with highly dispersed surface NiO was synthesized via structural topological transformation of layered double hydroxides. The catalyst exhibited excellent performance in furfural hydrogenation, achieving a 91.42% yield of FOL at 160 °C and 1.4 MPa H2. Gradual reduction of Ni2Al-LDO produced Ni/NiO mixtures, enabling a tunable shift from FOL to HFOL as NiO content decreased and metallic Ni content increased. After reduction at 700 °C for 2 hours, the HFOL yield reached 93.95% under identical conditions. CO2-TPD, NH3-TPD, and FT-IR analyses revealed that variations in reduction degree influenced furfural adsorption behavior. NiO species selectively adsorb the C=O group of furfural, with isopropanol serving as the hydrogen source via the Meerwein-Ponndorf-Verley (MPV) pathway, yielding FOL. In contrast, metallic Ni0 surfaces facilitate flat adsorption, enabling simultaneous activation of both the furan ring and carbonyl group, and can activate both H2 and isopropanol, with H2 as the primary hydrogen source, leading to complete hydrogenation to HFOL. This work elucidates a clear structure-activity relationship centered on the metal oxidation state and provides a practical reduction-engineering approach for designing adaptable catalysts in biomass upgrading.
SCIENCE CHINA Materials•2026•DOI: 10.1007/s40843-025-4143-9
High-Ni (Ni ≥ 0.9) layered cathodes are being developed to endure high-voltage operations above 4.5 V to boost energy density. However, they face exacerbated chemo-mechanical and electrochemical degradation under high-voltage operation, primarily due to excessive lattice strain and phase distortion during cycling. Here, we engineer a high-Ni, Co-free cathode featuring a multicomponent complex doping-modulated bulk structure, coupled with surface modification via a multifunctional atomic layer deposition-coated LiAlO2 layer. Such a unique framework achieved by surface-to-bulk integrated modification can not only greatly prevent lattice stress-induced mechanical degradation but also effectively mitigate the accumulation of by-products due to surface side-reactions. Moreover, the LiAlO2 nanoshell with exceptional ion conductivity markedly enhances the sur-/interfacial Li-ion migration kinetics, thus rendering low electron/ion-diffusion resistance. The developed cathode breaks through existing voltage constraints without compromising on performance, achieving an exceptional balance between capacity and cycle stability during operation at 4.8 V. Notably, the pouch-type cells utilizing graphite and Li metal anodes demonstrate excellent cyclability under demanding conditions, even operating at high charging cut-off voltages of 4.5 and 4.6 V, respectively.
SCIENCE CHINA Materials•2025•DOI: 10.1007/s40843-025-3510-0
The activity and stability of single-atom catalysts (SACs) are intimately associated with the structure of supports. Herein, by employing a van der Waals (vdW) heterostructure support, we construct a highly active and durable Pt SAC for hydrogen evolution reaction (HER). The unique support consists of monolayer MoS2 attaching on hierarchical N-doped carbon nanocages (hNCNC), on which Pt presents as individual single atoms on the hNCNC and as island-like single-atom layers on the MoS2. The optimized Pt1-MoS2/hNCNC demonstrates low overpotential (11 mV at 10 mA cm−2) and high mass activity (5.6 A mgPt−1 at −20 mV) in 0.5 M H2SO4 solution, outperforming commercial Pt/C. Impressively, the Pt1-MoS2/hNCNC exhibits improved long-term stability in proton exchange membrane water electrolyzer relative to commercial Pt/C. The excellent HER performance is attributed to the regulated electronic structure, robust interaction of Pt atoms with MoS2/hNCNC and facilitated charge transfer. This study establishes an innovative strategy to develop a highly active and durable Pt SAC using vdW heterostructure supports.